PC programmable temperature transmitter
+370 37 269444
Universally programmable via ReadWin® 2000
NAMUR NE 43
Specs at a glance
Input Pt100, Pt1000; TC type B, K, N, R, S Accuracy deviation 0.5 K (Pt100) Measuring range freely programmable, dependent of sensor Installation suitable for sensor head (form B) Product / Version Price / pcs. in EUR Order code Approval 1 to 3 4 to 10 11+ Non-hazardous area 47,- 43,- 39,- TMT80-AA
Product / Version Price / pcs. in EUR Order code Configuration kit TXU10- for PC-programmable devices. set-up programme+interface cable for PC with USB-Port. 4 pin plug + ReadWin2000 101,72 TXU10-AA
Prices valid until 30.09.2020 in EUR per unit (not including shipping and applicable sales tax). See
Endress+Hauser Terms and Conditions
Is this temperature transmitter not the perfect match for your application?
People who bought this also watched
The iTEMP TMT80 head transmitter can be installed in the form B sensor head. It has a 4 to 20 mA analog output.
The measuring range can be set up freely via ReadWin® 2000 configuration software. TMT80 can be used for resistance thermometers (RTD) as well as for most commonly used thermocouples.
The iTEMP TMT80 head transmitter converts the input signal into a linear 4 to 20 mA signal. It has measurement input for resistance thermometers (RTD) in 2-, 3- or 4-wire connection and thermocouples.
Input signal Resistance thermometer: Pt100, Pt1000 to IEC 60751 Thermocouples: type B, K, N, R, S Measurement range Dependent of applied sensor elementOutput Output signal 4 to 20 mA Failure signal To NAMUR NE 43 Max. load (Vpower supply -8 V)/0.025 A Input current required ≤3.5 mA Current limit ≤25 mA Switch on delay 4 s (during power up Ia ≈ 3.8 mA) Response time 1 sSignal on alarm Underranging Linear drop to 3.8 mA Overranging Linear rise to 20.5 mA Sensor breakage; sensor short circuit1) <3.6 mA or >21 mA can be set upElectrical connection Power supply Ub = 8 to 35 V DC Galvanic isolation Û = 0.5 kV Allowable ripple Uss ≤ 3 V at Ub ≥ 15 V, fmax = 1 kHz Reference conditions Calibration temperature 25 °C ±5 KAccuracy Influence of power supply ≤ ±0.01 %/V deviation from 24 V Load influence ≤ ±0.02 %/100 Ω Temperature drift
Pt100: Td = ±[(15 ppm/K × (measuring range end value – measuring range start value)) + (50 ppm/K × preset measurement range)] × Δθ
TC: Td = ±[(50 ppm/K × (Measurement range end value – measurement range start value)) + (50 ppm/K × preset measurement range)] × Δθ
Δθ = Deviation of ambient temperature according to the reference condition +25 °C ± 5 K (77 °F ± 9 °F)
Measurement accuracy 0.5 K (Pt100)Application conditions Ambient temperature –40 to +85 °C Storage temperature –40 to +100 °C Climatic class to EN 60654-1, Class C Vibration resistance 4 g / 2 to 150 Hz to IEC 60 068-2-6 EMC Interference immunity and interference emission according to IEC 61326 and NAMUR NE 21 Housing To DIN 50446 form B
1) Not for thermocouple
Dimensions (in mm)
Power supply and current output
Technical DatasheetMore documents for TMT80