Programmable temperature transmitter

PC programmable temperature transmitter

iTEMP TMT80

from €26,-
Need help?

Informacja - Zamówienia
+48 71 773 00 50

    • Universally programmable via ReadWin® 2000

    • NAMUR NE 43

    • Galvanic isolation

     

    Specs at a glance

    Input Pt100, Pt1000; TC type B, K, N, R, S
    Accuracy deviation 0.5 K (Pt100)
    Measuring range freely programmable, dependent of sensor
    Installation suitable for sensor head (form B)
    Product / VersionPrice / pcs. in EUROrder code
    Approval1 to 34 to 1011+
    Non-hazardous area32,-29,-26,- TMT80-AA

    Accessory

    Product / VersionPrice / pcs. in EUROrder code
    Configuration kit TXU10- for PC-programmable devices. set-up programme+interface cable for PC with USB-Port. 4 pin plug + ReadWin200099,23 TXU10-AA

    Prices valid until 30.06.2019 in EUR per unit (not including shipping and applicable sales tax). See
    Endress+Hauser Terms and Conditions
    The transaction will be settled with a VAT invoice in PLN after conversion according to the EUR exchange sell rate at the National Bank of Poland on the day of issuing the VAT invoice.

    Is this temperature transmitter not the perfect match for your application?

    People who bought this also watched

  • Application

    The iTEMP TMT80 head transmitter can be installed in the form B sensor head. It has a 4 to 20 mA analog output.

    The measuring range can be set up freely via ReadWin® 2000 configuration software. TMT80 can be used for resistance thermometers (RTD) as well as for most commonly used thermocouples.

    Function

    The iTEMP TMT80 head transmitter converts the input signal into a linear 4 to 20 mA signal. It has measurement input for resistance thermometers (RTD) in 2-, 3- or 4-wire connection and thermocouples.

  • Technical data

    Input
    Input signal Resistance thermometer: Pt100, Pt1000 to IEC 60751 Thermocouples: type B, K, N, R, S
    Measurement range Dependent of applied sensor element
    Output
    Output signal 4 to 20 mA
    Failure signal To NAMUR NE 43
    Max. load (Vpower supply -8 V)/0.025 A
    Input current required ≤3.5 mA
    Current limit ≤25 mA
    Switch on delay 4 s (during power up Ia ≈ 3.8 mA)
    Response time 1 s
    Signal on alarm
    Underranging Linear drop to 3.8 mA
    Overranging Linear rise to 20.5 mA
    Sensor breakage; sensor short circuit1) <3.6 mA or >21 mA can be set up
    Electrical connection
    Power supply Ub = 8 to 35 V DC
    Galvanic isolation Û = 0.5 kV
    Allowable ripple Uss ≤ 3 V at Ub ≥ 15 V, fmax = 1 kHz
    Reference conditions Calibration temperature 25 °C ±5 K
    Accuracy
    Influence of power supply ≤ ±0.01 %/V deviation from 24 V
    Load influence ≤ ±0.02 %/100 Ω
    Temperature drift

    Pt100: Td = ±[(15 ppm/K × (measuring range end value – measuring range start value)) + (50 ppm/K × preset measurement range)] × Δθ

    TC: Td = ±[(50 ppm/K × (Measurement range end value – measurement range start value)) + (50 ppm/K × preset measurement range)] × Δθ

    Δθ = Deviation of ambient temperature according to the reference condition +25 °C ± 5 K (77 °F ± 9 °F)

    Measurement accuracy 0.5 K (Pt100)
    Application conditions
    Ambient temperature –40 to +85 °C
    Storage temperature –40 to +100 °C
    Climatic class to EN 60654-1, Class C
    Vibration resistance 4 g / 2 to 150 Hz to IEC 60 068-2-6
    EMC Interference immunity and interference emission according to IEC 61326 and NAMUR NE 21
    Housing To DIN 50446 form B

     

    1) Not for thermocouple

    Dimensions (in mm)

    PC programmable temperature transmitter iTEMP TMT80 - Dimensions

    Installation according to operation instructions

    Electrical connection

    Power supply and current output

    PC programmable temperature transmitter iTEMP TMT80 - Electrical connection 1

    Sensor connection

    PC programmable temperature transmitter iTEMP TMT80 - Electrical connections 2

    a) two-wire RTD

    b) three-wire RTD

    c) four-wire RTD

    d) TC

    e) red

    f) white

  • More documents for TMT80